- Cisco receiver is getting ais code#
- Cisco receiver is getting ais series#
- Cisco receiver is getting ais mac#
To assign the interface address that is used by the device connecting to the router via PPP or SLIP, unless you override the address at the command line, use the async default ip address interface configuration command. Related CommandsĪccess-list (standard) async default ip address If nothing else in the access list matches, the default action is normally to deny access that is, filter out all other type codes. Use the last item of an access list to specify a default action for example, permit everything else or deny everything else. If you have both Ethernet Type II and LSAP packets on your network, you should set up access lists for both. If the latter is true, the packet is treated using type-code filtering.
![cisco receiver is getting ais cisco receiver is getting ais](https://img.yumpu.com/22914598/1/190x245/troubleshooting-the-cisco-1005-compucanjes.jpg)
If the length/type field is greater than 1500, the packet is treated as an LSAP packet unless the DSAP and SSAP fields are AAAA.
![cisco receiver is getting ais cisco receiver is getting ais](https://service.pcconnection.com/images/inhouse/EBE1E23C-DE0B-47D1-9D1A-67DF8F34F907.jpg)
Type-code access lists can have an impact on system performance therefore, keep the lists as short as possible and use wildcard bit masks whenever possible.Īccess lists are evaluated according to the following algorithm: This is because these two bits are used for purposes other than identifying the SAP codes.) (A mask for a DSAP/SSAP pair should always be at least 0x0101. Ethernet type codes are listed in the appendix "Ethernet Type Codes."ġ6-bit hexadecimal number whose ones bits correspond to bits in the type-code argument that should be ignored when making a comparison.
Cisco receiver is getting ais code#
You can specify either an Ethernet type code for Ethernet-encapsulated packets, or a DSAP/SSAP pair for 802.3 or 802.5-encapsulated packets. User-selectable number between 200 and 299 that identifies the list.ġ6-bit hexadecimal number written with a leading "0x" for example, 0圆000. access-list access-list-number type-code wild-mask Use the no form of this command to remove a single access list entry.
Cisco receiver is getting ais mac#
Use the access-list global configuration command to establish MAC address access lists. Support for these commands will cease in a future release.
![cisco receiver is getting ais cisco receiver is getting ais](https://image.slidesharecdn.com/2012ahapj-rffundamentals-130812110616-phpapp01/95/12012-ah-apj-rf-fundamentals-25-638.jpg)
Note Commands in this chapter that have been replaced by new commands continue to perform their normal functions in the current release but are no longer documented. For hardware technical descriptions, and for information about installing the router interfaces, refer to the hardware installation and maintenance publication for your particular product.įor interface configuration tasks and examples, refer to the chapter entitled "Configuring Interfaces" in the Router Products Configuration Guide.įor information about the Channel Interface Processor (CIP), see the chapter entitled "IBM Channel Attach Commands." The CIP is described in a separate chapter because of the interrelationship of host system configuration values and router configuration values. Thanks in advance.This chapter contains the commands used to configure nonprotocol-specific interface features. Line code, framing, etc are set as per Verizon's specs. Inserting a hard loop cable in the interface clears the alarm. The Alarm LED is lit as soon as we plug into the wall jack that goes to the smart card. Verizon has run loopback tests from their office and claim to "see" this router. Version info Firmware: 20000922, FPGA: 15įraming is ESF, Line Code is B8ZS, Clock Source is Line.ĭata in current interval (0 seconds elapsed):Ġ Line Code Violations, 0 Path Code ViolationsĠ Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded MinsĠ Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail SecsĪ show inteface says that Serial0/2:1 is reset. We need to connect this to a leased T1 line from Verizon.
![cisco receiver is getting ais cisco receiver is getting ais](https://blog.videgro.net/wp-content/uploads/2015/12/screenshot_openstreetmap_20151229_1705-672x372.png)
Cisco receiver is getting ais series#
I am trying to configure a Cisco VWIC-2MFT-T1-D1 interface card in a cisco 2600 series router.